Moisture Testers

Call for Pricing and Information or use the REQUEST FORM at the bottom of this page.
Component Sales & Service carries a large inventory of materials testing equipment and supplies.
If you have any questions regarding a listed product, or if you do not see the equipment you require,
please contact us at our toll free number 1-800-992-4205




James Cementometer™ Microwave Moisture Meter

The James Cementometer™ represents a break-through in modern moisture measurement technology. By utilizing the latest microwave and microprocessor science, the Cementometer™ can determine the moisture content of freshly mixed cement, concrete, and mortar. Simply insert the prongs of the probe into the material to be measured and instantaneously the water cement ratio is shown on the easy to read display.

The Cementometer™ Microwave moisture meter uses a two prong sensor to measure the complex dielectric constant of the material in contact with the prongs. As the dielectric constant of water is four to eight times greater than most aggregates and cements, changes in water content directly effect the sensor output. An average of five to ten readings is normally taken in order to ensure a valid reading. This output is then converted by the integrated microprocessor and moisture content is displayed directly.

Two units are available to encompass the full range of water cement ratio’s found in wet concrete. The Cementometer™ Type R handles normal water cement ratio’s with its two prong probe. The range of this instrument is approximately 0.35 to 0.65 water/cement. Cementometer™ Type L handles low water/cement ratio’s with its five prong probe. The range of this instrument is approximately 0.25 to 0.5 water cements.
Get Pricing       Get Information




Forney Moisture Meter LA-3401

Used to measure moisture content in concrete floors and screeds without drilling. Unit consists of a meter (powered by 9V battery), analog readout, co-planer electrodes on base for the transmission of parallel low frequency signals.
Get Pricing       Get Information




Forney Moisture Tester LA-3405

The "no wait" moisture test for fine aggregates and granular materials, including soils, sand,clay, and powders. Provides direct moisture reading after reaction with calcium carbide within 30 seconds. Kit contains Speedy™ vessel with gauge, Ohaus digital scale, scoop, cleaning brush, cleaning cloth, two steel pulverizing balls and case.
Get Pricing       Get Information




Humboldt Moisture Measurement System (MMS) H-2995

The Moisture Measurement System (MMS) is a powerful and versatile instrument for measuring concrete floor moisture, as well as a wide range of other dampness conditions in buildings. With the included probes, the user can switch between hygrometer and moisture meter modes to gain a thorough understanding of the extent of moisture or dampness related problems within the structure.
Get Pricing       Get Information




Humboldt Speedy® 2000 Moisture Tester H-4967

The Speedy® 2000 is a new moisture testing kit that combines the original Speedy tester with an electronic balance and a new, heavy-duty plastic carrying case. The new case offers the highest level of protection in the most demanding on-site conditions. The case incorporates tailor made foam insets that secure the contents and protect them from shock damage. The case itself is very durable. The electronic balance is used to weigh the sample before placing it into the Speedy tester. It is very simple to use, accurate and repeatable. The tester is supplied complete with electronic balance, beaker, cleaning cloth, cap, washer, scoop, steel pulverizing balls and cleaning brushes.
The stored measuring data can be directly printed by means of a printer or transferred to a PC.
Get Pricing       Get Information




Gilson Speedy 2000 Moisture Tester MA-25

The Speedy® 2000 Moisture Testers are widely accepted for rapid, accurate, and reliable moisture tests on all kinds of materials–sand, aggregates, ores, coal, soils, ceramics, abrasives, and other powders and chemicals. Units are portable, easy to use and do not require a power supply. Samples can be tested on-site, eliminating risk of moisture loss during transport.
The stored measuring data can be directly printed by means of a printer or transferred to a PC.
Get Pricing       Get Information




James Trident™ Moisture Tester T-T-90

A Microwave meter for rapid determination of moisture content in sand and other fine and coarse aggregates. The Trident™ T-T-90 utilizes the latest microwave and microprocessor technology to measure moisture content in various fine and coarse-grained materials. The prongs of the probe are inserted into the material to be tested and the percentage of moisture content is instantaneously shown on the easy to read display. An average of five to ten readings is normally taken in order to ensure a valid result. This output is converted by the integrated microprocessor and the moisture content is displayed directly as a percentage of dry weight. The Trident™ comes calibrated for both sand and aggregate, and can be programmed by the user with up to ten different materials. The Trident™ can store more than 150 readings - complete with time and date for future reference. Data can be recalled via RS-232 interface to a personal computer.
Get Pricing       Get Information




James Aquameter™ Moisture Tester T-M-70

The James Aquameter™ is an advanced digital instrument, using a high frequency capacitive sensor to accurately measure the water content of concrete, masonry, brick, gypsum and most solid materials. Through extensive testing of various materials, relationships between changes in the dielectric constant and moisture content have been determined - and computed and digitized in the Aquameter™s. This gives the user a direct read-out of moisture content for a variety of materials. No charts or tables required - no prongs, probes or holes needed. Model T-M-70 features additional functions allowing the user to calibrate the meter to determine moisture content in almost any solid material. Also, it can automatically average an infinite number of readings to determine the moisture content of large structures.
Get Pricing       Get Information


 

Please check all information you provide  
Required Information ®
Your Name: ®
E-Mail: ®
Address:
City:
State or Province:
Postal Code (Zip):
Country:
Phone:
FAX No.:
How would you prefer to be contacted with your information?
Email   Mail   Phone   FAX  
Please enter additional comments or questions in the box below:

Please contact as soon as possible regarding this Quote.




Click only once to submit request!
 
Please note that, Component Sales & Service, Inc. has limited distribution areas on some products within the United States
Inquires made from States that are not in our contractual area shall be redirected to the manufacture or regional distributor


[ FAQ | CONCRETE | ASPHALT | SOIL | PRODUCTS | SERVICES | RFI | RFQ | SITE MAP | LINKS | TERMS | ABOUT US | EMAIL ]
Thank you for using Component Sales & Service Inc.