Component Sales & Service - Sample Ejector and Soil Sampling

Sample Ejector and Soil Samlping

Call for Pricing and Information or use the REQUEST FORM at the bottom of this page.
Component Sales & Service carries a large inventory of materials testing equipment and supplies.
If you have any questions regarding a listed product, or if you do not see the equipment you require,
please contact us at our toll free number 1-800-992-4205

Please check all information you provide
Required Information ®

Your Name: ®
E-Mail: ®
Address:
City:
State or Province:
Postal Code (Zip):
Country:
Phone:
FAX No.:

How would you prefer to be contacted with your information?
Email Mail Phone FAX
Please enter additional comments or questions in the box below:

Please contact as soon as possible regarding this Quote.

Click only once to submit request!

Please note that, Component Sales & Service, Inc. has limited distribution areas on some products within the United States
Inquires made from States that are not in our contractual area shall be redirected to the manufacture or regional distributor

	Power Soil Auger Sampler For soil sampling, construction and more, earth augers are gasoline powered and portable. Using one operator, they allow fast and easy drilling. They feature snap-on or screw-on augers and extensions. Engine mounted on wheel-base carrier keeps motor noise and fumes away from the operator. Torque tube eliminates counter torque. Features such as the carrier and torque tube offer greater mobility, beneficial in areas inaccessible to large equipment, on slopes and horizontal drilling, various standard sampling methods to obtain material samples. Recoil starter and spring-loaded throttle-in-handle assembly provide fingertip control. Centrifugal clutch, heavy-duty flexible shaft connects to the motor and provides for a smooth operation. Blades and points are tool steel, hard-surfaced and heat treated. Blades are reversible for longer life. Most augers are snap-on design; smaller diameter augers are screw-on. Humboldt H-4050 Get Pricing Get Information
	Sampling Auger Probe Sampling Auger Probe is designed especially for sampling of fine powders that tend to compact, making insertion of normal probes difficult. Ideal for powdered metals and chemicals. Construction is double-tube, 1" O.D. (25.4 mm) and 39" long (991 mm). There are 13 sample openings with partitions between openings; inner tube rotates to close openings for removal. An auger vane is brazed onto bottom 13" (330 mm) of outer tube, and a "T" handle is welded to top for augering. Gilson GP-118 Get Pricing Get Information
	Cross Handle & Extensions For use with various AMS Augers and samplers, the Cross Handle has a baked-on rubber coating for comfort and electric shock protection. Extensions in 2 ft. to 5 ft. (0.6-1.5m) lengths are aircraft quality chrome molybdenum seamless construction. Gilson SP-180 Get Pricing Get Information
	AMS Augers AMS augers are available for a wide range of soil conditions. All use manual cross handles and extension rods, ordered separately. Augering up to 5 ft. (1.5m) in less than two minutes and to total depths of up to 30 ft. (9.1m) may be achieved with most types. Augers make holes about 3/8" to 3/4" (9.5-19.1mm) larger than cylinder sizes. They have strong carbon steel bails and hard-drawn stainless steel cylinders welded to bits forged from high-carbon alloy steel. Sharpened edges are heat treated stellite. Standard Augers are for ordinary soils. Mud Augers are for heavy wet soils and clays, and Sand Augers are for dry sandy soils. All are available in four sizes. Gilson SP-250 - SP-283 Get Pricing Get Information
	One Piece Soil Sampler One piece 19" Long with Open Sleeve T-handle soil samplers take 3/4" (19mm) diameter cores using 15/16" (24mm) OD sampling tubes with replaceable screw-on hardened tips. Construction is welded high-quality reinforced plated steel. Humboldt H-4269 Get Pricing Get Information Gilson SP-138 Get Pricing Get Information
	Motorized Sample Ejector Similar in design and construction to the Hand operated heavy duty sample ejector, this model features the use of a 5-ton capacity motorized hydraulic pump and ram assembly. The unit incorporates extended upright rods in order to accommodate both standard 4" or 6" asphalt and soil compaction molds as well as the taller gyratory compaction molds. Humboldt H-1355 Get Pricing Get Information
	Portable Sample Ejector The Portable Sample Ejector is powered by an 8000 lbf (35.6 kN) manual hydraulic jack. The versatile HM-520R includes all discs and adapter plates to push samples from 2" and 3" diameter thin-walled soil tubes or 4" and 6" diameter soil or asphalt molds. Pusher discs attach quickly to piston. Adapter plates fit quickly into upper reaction frame. Reaction frame is supported by dual columns, each with three holes for pin mounting. Sample ejecting starts in top position. Then, the frame is dropped for additional jacking at the other two locations until sample is free. Humboldt H-1353A Get Pricing Get Information Gilson HM-517 Get Pricing Get Information
	Motorized Hydraulic Sample Ejector Provides a very efficient and easy means for rapid ejection of samples from standard 3" (76.2mm) thin wall sample tubes. When operated in the standard vertical position, the ejector requires only a maximum height of 76" (1,930mm) when extruding samples from a 36" (914mm) long tube. In operation, two electrically driven cylinders, working in tandem, are used to pull the tube down in 20" (508mm) increments. The tube gripper assembly was specifically designed to securely hold the thin wall tube in place and quickly release when the ejection process has completed without damaging the tube. Humboldt H-4157B Get Pricing Get Information Gilson HM-522 Get Pricing Get Information